An Investigation of Thin Feature Generation in Direct Metal Laser Sintering Systems

Keywords

Feature (linguistics), Selective laser sintering, Laser, Sintering, Materials science

References

• CHARACTERIZATION OF THIN WALLED Ti-6Al-4V COMPONENTS PRODUCED VIA ELECTRON BEAM MELTINGDenis Cormier, Harvey West, Ola Harrysson — 2004
• Structural Design, Optimization and Application of 3D Re-entrant Auxetic Structures.Li Yang — 2011
• Evaluations of cellular lattice structures manufactured using selective laser meltingChunze Yan, Liang Hao, Ahmed Hussein — 2012
• Auxetic cellular structures through selective electron‐beam meltingJan Schwerdtfeger, Peter Heinl, Robert F. Singer — 2010
• Cellular Titanium by Selective Electron Beam MeltingPeter Heinl, Andreas Rottmair, Carolin Körner — 2007
• Parametric analysis of the selective laser melting processIgor Yadroitsev, Ph. Bertrand, I. Smurov — 2007
• A Comparison of Bending Properties for Cellular Core Sandwich PanelsLi Yang, Ola Harrysson, Harvey West — 2013
• Selective Electron Beam Melting of Cellular Titanium: Mechanical PropertiesPeter Heinl, Carolin Körner, Robert F. Singer — 2008
• Compression fatigue behavior of Ti-6Al-4V mesh arrays fabricated by electron beam meltingS.J. Li, L.E. Murr, Xiaoying Cheng — 2012
• Compressive behaviour of stainless steel micro-lattice structuresRecep Gümrük, R. A. W. Mines — 2013
• Characterization of Ti–6Al–4V open cellular foams fabricated by additive manufacturing using electron beam meltingL.E. Murr, S.M. Gaytan, Frank Medina — 2010
• The development of a scanning strategy for the manufacture of porous biomaterials by selective laser meltingR. Stamp, Peter Fox, W O’Neill — 2009
• The Mechanical Properties of Sandwich Structures Based on Metal Lattice ArchitecturesYiou Shen, S. McKown, S. Tsopanos — 2010
• The Influence of Processing Parameters on the Mechanical Properties of Selectively Laser Melted Stainless Steel Microlattice StructuresS. Tsopanos, R. A. W. Mines, S. McKown — 2010
• Open-cellular copper structures fabricated by additive manufacturing using electron beam meltingD.A. Ramirez, L.E. Murr, Shujing Li — 2011
• Structural, mechanical and in vitro characterization of individually structured Ti-6Al-4V produced by direct laser forming.Dirk A. Hollander, Matthias Walter, Tobias Wirtz — 2006

Cited by

• Design for Additively Manufactured Lightweight Structure: A PerspectiveLi Yang, Ola L. A. Harrysson, Denis Cormier — 2016
• Design, analysis, and application of a cellular material/structure model for metal based additive manufacturing process.Shanshan Zhang — 2017
• Exploration of Metal 3-D Printing Technologies for the Microfabrication of Freeform, Finely Featured, Mesoscaled StructuresZhumei Sun, Gleb Vladimirov, Е. Н. Николаев — 2018
• Beautiful and Functional: A Review of Biomimetic Design in Additive ManufacturingAnton du Plessis, Chris Broeckhoven, Ina Yadroitsava — 2019
• A design framework for additive manufacturingHarry Bikas, Andreas K. Lianos, Panagiotis Stavropoulos — 2019
• Laser Additive Manufacturing using directed energy deposition of Inconel-718 wall structures with tailored characteristicsA.N. Jinoop, C. P. Paul, Sanjay Mishra — 2019
• A review of geometric sensitivities in laser metal 3D printingVedant Chahal, Robert M. Taylor — 2020
• Accuracy of complex internal channels produced by laser powder bed fusion processFlaviana Calignano, O. A. Peverini, Giuseppe Addamo — 2020
• Additively Manufactured Robust Microfluidics via Silver Clay ExtrusionEmmanuel Segura-Cárdenas, Luis Fernando Velásquez–García — 2020
• Low-Cost, Rugged Microfluidics via Silver Clay ExtrusionEmmanuel Segura-Cárdenas, Luis Fernando Velásquez–García — 2019
• Powder thermal conductivity measurements in laser powder-bed fusion: an uncertainty study with sensitivity analysisShanshan Zhang, Brandon Lane, Kevin Chou — 2021
• FEM Simulations for the Optimization of the Inlet Gate System in Rapid Investment Casting Process for the Realization of Heat ExchangersDaniele Almonti, Gabriele Baiocco, Emanuele Mingione — 2021
• Low-Cost, Rugged Microfluidics via Silver Clay ExtrusionEmmanuel Segura-Cárdenas, Luis Fernando Velásquez–García — 2019
• Laser powder bed fusion additively manufactured thin lightweight Ti6Al4V features: an experimental investigation on the influence of powder feedstock, geometry, and process parameters on property/qualityNaresh Koju, J. Hermes, Sayed Ehsan Saghaian — 2023
• Prediction of residual stresses in additively manufactured parts using lumped capacitance and classical lamination theoryJose Mayi-Rivas, Quentin Fouliard, Jeffrey R. Bunn — 2024
• Prediction of Residual Stresses in Additively Manufactured Parts Using Lumped Capacitance and Classical Lamination TheoryJose Mayi-Rivas, Quentin Fouliard, Jeffrey R. Bunn — 2023
• Property Evaluation of Metal Cellular Strut Structures via Powder Bed Fusion AMShanshan Zhang, Samuel Dilip, Li Yang — 2015
• Design for Additive ManufacturingLi Yang, Keng Hsu, B. Baughman — 2017

Related papers

• DMLS and ManufacturingOlli Nyrhilä, Juha Kotila, Maria Latikka — 2007
• Use of Direct Metal Laser Sintering for Tooling in High Volume ProductionJoel W. Hendrickson — 2015
• Selective laser sintering of metallic powder for microfabrication technologyY.P. Kathuria — 1997
• Dimensional Accuracy of a Product Built Using Direct Metal Laser SinteringPavel Hanzl, Ivana Zetková, Jan Kutlwašer — 2018
• DEVELOPMENT OF AN EXPERIMENTAL LASER SINTERING MACHINE TO PROCESS NEW MATERIALS LIKE NYLON 6Johannes Lohn, C. Kummert, Hans‐Joachim Schmid — 2017
• The fabrication of thin wall structure with novel laser vaporizing sinteringJimin Chen, Pengfei Lv, Daqing Sun — 2008
• A simulation model for direct selective laser sintering of metal powdersX. C. Wang, J.-P. Kruth — 2000
• Direct metal laser sintering for rapid tooling: processing and characterisation of EOS partsM.W Khaing, Jerry Ying Hsi Fuh, Li Lü — 2001
• An overview of investigation of Fatigue, tensile strength and hardness of the components fabricated through direct metal laser sintering (DMLS) processNagendra Kumar Maurya, Rohit Sharma, Nikhil Kumar — 2021