Experimental study of the wear behavior of PCBN inserts during cutting of GH4169 superalloys under high-pressure cooling

Keywords

Superalloy, Tool wear, Coolant, Machinability, Materials science

References

• The machinability of nickel-based alloys in high-pressure jet assisted (HPJA) turningDavorin Kramar, Milenko Sekulić, Zoran Jurković — 2013
• Study on high-speed machining of Inconel 718 focusing on tool surface topography of CBN cutting toolTatsuya Sugihara, Shota Takemura, Toshiyuki Enomoto — 2016
• Effect of high-pressure coolant supply when machining nickel-base, Inconel 718, alloy with coated carbide toolsE. O. Ezugwu, J. Bonney — 2004
• A finite element analysis of thermal relaxation of residual stress in laser shock processing Ni-based alloy GH4169Xudong Ren, Q. Zhan, Shuxia Yuan — 2014
• Study on the machinability characteristics of superalloy Inconel 718 during high speed turningD. G. Thakur, B. Ramamoorthy, L. Vijayaraghavan — 2009
• High-speed Machining of Inconel 718 with Ceramic ToolsNorihiko Narutaki, Yasuo Yamane, Katsura Hayashi — 1993
• Temperature and wear of cutting tools in high-speed machining of Inconel 718 and Ti6Al6V2SnTakeaki KITAGAWA, Akihiko Kubo, K. Maekawa — 1997
• Tool life and wear mechanisms in high speed machining of Ti–6Al–4V alloy with PCD tools under various coolant pressuresRosemar B. da Silva, Álisson Rocha Machado, E. O. Ezugwu — 2013
• Tool-life and wear mechanisms of CBN tools in machining of Inconel 718Jean-Philippe Costes, Y. Guillet, Gérard Poulachon — 2007
• Evaluating the effect of coolant pressure and flow rate on tool wear and tool life in the steel turning operationAnselmo Eduardo Diniz, Ricardo Micaroni, Amauri Hassui — 2010
• Turning performance optimisation of aeronautical materials by using high pressure cooling technologyCarmen Sanz, Elena Fuentes, Óscar Gonzalo — 2007
• Finish Machining of Nickel-Base Inconel 718 Alloy with Coated Carbide Tool under Conventional and High-Pressure Coolant SuppliesE. O. Ezugwu, J. Bonney — 2005
• Wear mechanisms of WC coated and uncoated tools in finish turning of Inconel 718Abhay Bhatt, Helmi Attia, R. Vargas — 2010
• Effect of Machining Parameters on Surface Integrity in High Speed Milling of Super Alloy GH4169/Inconel 718Waseem Akhtar, Jianfei Sun, Wuyi Chen — 2016
• Influence of High-pressure Flushing through the Rake Face of the Cutting ToolR. Wertheim, J. Rotberg, A. Ber — 1992
• Dynamic recrystallization behavior of a typical nickel-based superalloy during hot deformationXiao-Min Chen, Y.C. Lin, Dong-Xu Wen — 2014
• Investigation and optimization of lubrication parameters in high speed turning of superalloy Inconel 718D. G. Thakur, B. Ramamoorthy, L. Vijayaraghavan — 2010
• Optimization of Machining Performance in High-Pressure Assisted Turning of Ti6Al4V AlloyOğuz Çolak — 2014
• High speed machining of aero-engine alloysE. O. Ezugwu — 2004
• Employing preheating- and cooling-assisted technologies in machining of Inconel 718 with ceramic cutting tools: towards reducing tool wear and improving surface integrityKejia Zhuang, Xiao-Ming Zhang, Dahu Zhu — 2015

Cited by

• Experimental investigation of IN725 under different cooling environments using new tool holderSahil Gupta, K. Venkatesan, S. Devendiran — 2018
• Deposition of Trace Coolant Elements on Flank Face in Turning of mboxInconel 718 Under High Pressure ConditionsToshiyuki OBIKAWA, Zhenglong Fang, Wataru Matsumoto — 2019
• Cutting Performance and Wear/Damage Characteristics of PCBN Tool in Hard MillingHaining Gao, Xianli Liu, Zhitao Chen — 2019
• Design and performance of an internal-cooling turning tool with micro-channel structuresRuitao Peng, Haojian Jiang, Xinzi Tang — 2019
• FEM Simulation and Experiment of High-Pressure Cooling Effect on Cutting Force and Machined Surface Quality During Turning Inconel 718Li Liu, Mingyang Wu, Lubin Li — 2020
• Effects of deep cryogenic treatment on WC-Co cutter performances in milling of superalloy GH536Dong Liu, Gao Li, Peng Zhou — 2020
• Experimental Study on Tool Wear in Cutting Superalloy under High-Pressure CoolingMingyang Wu, Shu-Jie Wu, Weixu Chu — 2020
• Assessment of tool wear mechanisms in high-pressure jet-assisted turning process of a nickel-based superalloyGholamali Nasr, Mohammadreza Soltantarzeh, Behnam Davoodi — 2020
• A review on cutting tool technology in machining of Ni-based superalloysWei Fan, Wei Ji, Lihui Wang — 2020
• Development of a pressurized internal cooling milling cutter and its machining performance assessmentRuitao Peng, Jiachen Liu, Meiliang Chen — 2021
• Study on the reaming process of aluminum alloy 7050-T7451 under different cooling conditionsZi Ye, Yongguo Wang, Xin Yu — 2021
• High-pressure flank cooling and chip morphology in turning Alloy 718Nageswaran Tamil Alagan, Pavel Zeman, Vladimír Mára — 2021
• Experimental Study on Surface Roughness and Flank Wear in Turning of Nimonic C263 under Dry Cutting ConditionsJ. Francis Xavier, B. Ravi, D. Jayabalakrishnan — 2021
• Modelling and Simulation of Machining Attributes in dry Turning of Aircraft Materials Nimonic C263 using CBNSrinivasan Senthil Kumar, M. P. Sudeshkumar, C. Ezilarasan — 2021
• Tool wear and its effect on the surface integrity and fatigue behavior in high-speed ultrasonic peening milling of Inconel 718Xiaoming Yin, Yihang Liu, Shicai Zhao — 2022
• Optimization analysis of microtexture size parameters of tool surface for turning GH4169Xinmin Feng, Cong Meng, Wei Lian — 2023
• Research on Cutting Layer Characteristics of Superalloy under High-Pressure CoolingLubin Li, Shuning Chen, Tiankang Li — 2023
• Research on Cutting Temperature of GH4169 Turning with Micro-Textured ToolsXinmin Feng, Xiwen Fan, Jingshu Hu — 2023
• High surface integrity machining of typical aviation difficult-to-machine material bladeDongbo Wu, Shibo Liu, Hui Wang — 2023
• A Comprehensive Review of Machinability of Difficult-to-Machine Alloys with Advanced Lubricating and Cooling TechniquesDanil Yurievich Pimenov, Leonardo Rosa Ribeiro da Silva, Álisson Rocha Machado — 2024

Related papers

• Closure to “Discussions of ‘Machinability of Nodular Cast Irons: Part II—Effect of Cutting Conditions on Flank Adhesion’” (1962, ASME J. Eng. Ind., 84, p. 288)Kenichi Hitomi, G. L. Thuering — 1962
• A tool wear observer model for flank wear monitoring in the milling of Nickel-based alloysHuaizhong Li, Andreas Albrecht, Xiaoqi Chen — 2009
• Experimental study on machinability improvement of hardened tool steel using two dimensional vibration-assisted micro-end-millingHui Ding, Rasidi Ibrahim, Kai Cheng — 2010
• Analysis of The Chip Formation of Bainitic Steel in Drilling ProcessesDarko Smolenicki, Jens Boos, Friedrich Kuster — 2012
• Tool flank wear recognition based on the variation of milling force vector in end millingYongfeng Hou, Dinghua Zhang, Ming Luo — 2014
• ON CHIP FORMATION DURING DRILLING OF CAST ALUMINUM ALLOYSJules Kouam, Victor Songméné, Yasser Zedan — 2013
• A NEW CONCEPT FOR DECOUPLING THE CUTTING FORCES DUE TO TOOL FLANK WEAR AND CHIP FORMATION IN HARD TURNINGJ. Y. Wang, C. R. Liu — 1998
• MACHINABILITY OF SOME FIBER-REINFORCED THERMOSET AND THERMOPLASTICS IN DRILLINGH. Hocheng, H. Y. Pwu, Kuo-Ching Yao — 1993
• FNN based online monitoring of flank wear during turning of EN-31 steelAlakesh Manna, Sandeep M. Salodkar — 2010