Effect of Strain Rate Upon Plastic Flow of Steel

Keywords

Isothermal process, Materials science, Strain rate, Adiabatic process, Plasticity

References

• The Latent Energy Remaining in a Metal after Cold WorkingGeoffrey Ingram Taylor, H. Arthur Quinney — 1934

Cited by

• DEFORMATION BEHAVIOR OF A535 ALUMINUM ALLOY UNDER DIFFERENT STRAIN RATE AND TEMPERATURE CONDITIONSM. Rezaei — 2014
• Deformation Behaviour of C-Mn440 Automobile Steel under Varying Strain Rates.Awanish Kumar Mishra — 2014
• Vers une modélisation physique de la coupe des aciers spéciaux : intégration du comportement métallurgique et des phénomènes tribologiques et thermiques aux interfacesC. Courbon — 2011
• Dynamic Ferrite Transformation in Fe-6Ni-0.1C AlloyNokeun Park — 2013
• Localization of Deformation in Heterogeneous Solids Deformed at High Strain RatesBryan Love, R.C. Batra — 2005
• Large strain computational modeling of high strain rate phenomena in perforating gun devices by Lagrangian/Eulerian FEM simulationsLuca Gambirasio — 2013
• Failure mode transitions in polymers under high strain rate loadingK. Ravi‐Chandar, Jie Lü, Bo Yang — 2000
• Asymptotic integration algorithms for first-order ODEs with application to viscoplasticityAlan D. Freed, Minwu Yao, Kevin Walker — 1992
• Transformed shearing bands in strongly impact loaded 30CrMnSiA steelJianli Zhou, L. Zhen, Yanhui Cui — 1998
• A correlation between tensile flow stress and Zener-Hollomon factor in TiAl alloys at high temperaturesYu Wang, Dongliang Lin, C. C. Law — 2000
• The design of advanced performance high strength low-carbon martensitic armour steels: Part 1. Mechanical property considerationsKasonde Maweja, W.E. Stumpf — 2008
• Numerical Simulation of Adiabatic Shear Bands in Ti-6Al-4V Alloy Due to Fragment ImpactFermen-Coker, Muege — 2005
• Determination of the Deformation State of a Ti-6Al-4V Alloy Subjected to Orthogonal Cutting Using Experimental and Numerical MethodsAquidul Islam — 2012
• The characterisation of white-etching layers formed on engineering steelsR. Bulpett — 1991
• Plastic Shearing at Very High Strain Rates, A ReviewJ. R. Klepaczko — 1996
• A viscoplastic model with application to LiF-22 percent CaF2 hypereutectic saltAlan D. Freed, Kevin Walker — 1990
• Advanced Modeling for Ductile Behavior of Materials Under High Strain Rates and Temperature Using Continuum Damage Mechanics and Solid State EquationsNicola Bonora — 2001
• New Sliding Surface Techniques Enable the Simulation of Target Plugging FailureB. E. Ringers — 1983
• Brittle-to-ductile transition temperature and its strain rate sensitivity in a two-phase titanium aluminide with near lamellar microstructureYu Wang, Dongliang Lin, C. C. Law — 1999
• Effects of strain rates on deformation twinning behavior in α-titaniumTongbo Wang, Bolong Li, Mian Li — 2015

Related papers

• Study on hot deformation behaviour and microstructure of Zr-4 alloyXuan Zhou, Kelu Wang, Xin Li — 2020
• A Study of the Technique of LD11 Alloy in Isothermal DeformationJian Cui — 2000
• Deformation Behavior and Processing Map during Isothermal Hot Compression of 49MnVS3 Non-Quenched and Tempered SteelQingjuan Wang, Jiamin Shi, Jun Cai — 2018
• Flow Stress Behaviors of the Elevated Temperature Compression Deformation for Al-8.4Zn-2.2Mg-2.4Cu AlloyYuan Ge — 2003
• Study on the Flow Stress of the High-Mn Austenitic Steel during Hot DeformationXin Xu, Fang Po Li, Chun Feng — 2013
• Flow stress model considering contribution of strain in isothermal compression of 7A09 aluminum alloyWU Juan-li — 2011
• Hot Deformation Behavior and Processing Maps of Pure Copper during Isothermal CompressionTiantian Chen, Ming Wen, Hao Cui — 2023
• Analysis of high flow stress and microstructural evolution of TC6 titanium alloy during isothermal forgingAo Xiong, M.-Q. Li, Wei Huang — 2004
• Study on Hot Deformation Behavior of Zinc Based AlloyChunhua Zhou — 2008