Process Modeling of Orthogonal Cutting by the Rigid-Plastic Finite Element Method

Keywords

Microscale chemistry, Finite element method, Materials science, Chip formation, Plane stress

References

No references recorded for this paper.

Cited by

• Micromilling mechanism : research and realizationJinsheng Wang — 2009
• Modelling of stagnant zone formation on diamond cutting tool when turning titanium alloyThet Mon Thet — 2007
• Simulation des processus de génération de contraintes résiduelles en tournage du 316L : nouvelle approche numérique et expérimentaleFrédéric Valiorgue — 2008
• Modelling of temperature profile in turning with uncoated and coated cemented carbide insertRam Chandra Kisku — 2011
• Determination of the Deformation State of a Ti-6Al-4V Alloy Subjected to Orthogonal Cutting Using Experimental and Numerical MethodsAquidul Islam — 2012
• Theoretical modelling and animation of the chip curling process in 3-D metal cuttingYijiang Fang — 1998
• A Heat Partition investigation of Multilayer Coated Carbide Tools for High Speed Machining through experimental studies and Finite Element ModellingMuhammad Fahad — 2012
• Finite element modelling (including material grain refinement prediction) when turning advanced aerospace alloysRaul E. Munoz — 2015
• Evaluation on models of calculating energy consumption in metal cutting processes: a case of external turning processQianqian Zhong, Renzhong Tang, Jingxiang Lv — 2016
• Finite Element Modeling of Hard TurningIbrahim Al-Zkeri — 2007
• Modélisation hybride du frottement local à l'interface outil-copeau en usinage des alliages métalliquesSlim Bahi — 2010
• Finite Element Method Applied on Metal Cutting: from Chip Formation to Coating Delamination by Tribo-Energetic Approach‪Armansyah Ginting — 2010
• Hybrid deflection prediction for machining thin-wall titanium alloy aerospace componentRohana Abdullah — 2011
• Computational machining of titanium alloy : Finite element modeling and a few resultsT. Obikawa, E. Usui — 1996
• Modelling Requirements for Computer Simulation of Metal MachiningM. Hüsnü Dirikolu — 2000
• Analysis of stresses in abrasive waterjet machining (AWJM)Ashraf I. Hassan, J. Kosmol, J. Bursa — 2000
• FINITE ELEMENT MODELING OF STRESS DISTRIBUTION IN THE CUTTING PATH IN MACHINING OF DISCONTINUOUSLY REINFORCED ALUMINIUM COMPOSITESRaviraj Shetty, Laxmikant G. Keni, Raghuvir Pai — 2008
• The transient beginning to machining and the transition to steady-state cuttingP.A.R. Rosa, O. Kolednik, P.A.F. Martins — 2007
• Built-up edge analysis of orthogonal cutting by the visco-plastic finite-element methodJeong‐Du Kim, V. Marinov, Dong‐Sik Kim — 1997
• FINITE ELEMENT MODELING OF BURR FORMATION IN METAL CUTTINGSangkee Min, David Dornfeld, Jinsoo Kim — 2001

Related papers

• The development of a microscale strain measurement system applied to sheet bulge hydroformingWilliam J. Emblom, Richard J. Jones, Mitra Aithal — 2014
• PRACTICAL APPLICATION OF MICROSCALE LABORATORYZheng Zi — 2000
• Experimental methodology and theoretical framework in describing constrained plastic flow of FCC microscale tensile specimensH.T. Vo, Evan K. Still, Kiet Lam — 2021
• The Effect of Microstructure on Chip Formation and Surface Defects in Microscale, Mesoscale, and Macroscale Cutting of SteelAndy Simoneau, E. Ng, M.A. Elbestawi — 2006
• Analysis of Stress-strain in the Plastic StateZhang Li — 2001
• Effective stress and strain in finite deformationZhou Zhe, Qin Ling-li, Huang Wen-bin — 2004
• Strength assessment of earth damsT.Z. Sultanov, Bakhtiyor Yuldoshev, Elyor Toshmatov — 2019
• A comparative analysis of the mesoscale stress-strain state in two- and three-dimensional polycrystalline specimensВ. А. Романова, Р. Р. Балохонов, Siegfried Schmauder — 2010
• AN ANALYSIS OF THE MODELING OF STRESS AND STRAIN FIELDS IN A REAL MICROSTRUC-TURE USING AHYBRID METHODKang Yilan, Э. Соппа, Siegfried Schmauder — 2002