Dislocations and the Mechanical Properties of Crystals

Keywords

Materials science, Crystallography, Chemistry

References

No references recorded for this paper.

Cited by

• MECHANISMS OF DEFORMATION IN DISPERSION-HARDENED ALLOYS.P. Guyot — 1966
• Thermodynamics-based design of creep resistant Mg solid solutions using the Miedema schemeSaeideh Abaspour — 2015
• STACKING FAULT ENERGY, ORDERING AND TRANSGRANULAR STRESS CORROSION CRACKING IN AUSTENITIC ALLOYSD. L. Douglass, G. Thomas, W. Roser — 1963
• A Multi-Scale Theoretical Scheme for Metal DeformationRobb Thomson, Retired, Lyle E. Levine — 2002
• Non-hookean, premacroyield stress-strain behavior of several ionic single crystalsE. R. Gotsky, C. A. Stearns — 1964
• Size-Dependent Plasticity in Twinned Metal NanowiresFrédéric Sansoz, Chuang Deng — 2012
• Nanocrystalline alloys : enhanced strengthening mechanisms and mechanically-driven structural evolutionTimothy J. Rupert — 2011
• Mechanism-based constitutive modeling of L1₂ single-crystal plasticityYuan Yin — 2006
• NASA Microgravity Materials Science ConferenceFrank R. Szofran, D. McCauley, C. Walker — 1996
• Damping studies of point defect migration in stainless steelN. F. Fiore, D. C. Stewart — 1970
• Dislocation Pile-Ups, Material Strength Levels, and Thermal ActivationRonald W. Armstrong — 2016
• Development of advanced numerical algorithms for kinetic and dynamic simulations of irradiated systems : kinetic Monte Carmelo and dislocation dynamicsE. Sáez — 2011
• INFLUENCE OF INTERSTITIALS ON THE MECHANICAL PROPERTIES OF GROUP IV b METALS.P. Rodríguez, V. Arunachalam — 1968
• The Portevin-Le Chatelier Effect in the Ni-Based Superalloy IN100Patxi Fernandez-Zelaia, Benjamin S. Adair, Vincent M. Barker — 2015
• Thermodynamics-Based Selection and Design of Creep-Resistant Cast Mg AlloysSaeideh Abaspour, C.H. Cáceres — 2015
• Al-Si Cast Alloys - Microstructure and Mechanical Properties at Ambient and Elevated TemperaturesMohammadreza Zamani — 2015
• Thermal shock-induced fracture of ion-implanted LiF crystalsV.N. Gurarie, J. S. Williams — 1990
• A Material Genomic Design of Advanced High Performance, Non-Corroding Steels for Ambient and High Temperature ApplicationsQi Lu, Wei Xu, Sybrand van der Zwaag — 2014
• Effect of point defects on one-dimensional compression of a latticeM. A. Mogilevskii, I. O. Mynkin — 1978
• The fracture of metalsJ. R. Low — 1963

Related papers

• Effects of SiC contents on the microstructure and mechanical properties of Al4SiC4–SiC ceramic compositesHuan Liu, Huihui Zhang, Ming Zhu — 2023
• Porous SiC Ceramics with Multiple Pore Structure Fabricated via Gelcasting and Solid State SinteringFeng Wang, Zhao-Fen Gao, Xu Jiaqiang — 2016
• Elevated temperature compressive properties of reaction milled NiAl–AlN and Zr-doped NiAl–AlN compositesJ. Daniel Whittenberger, Michael J. Luton — 1992
• Effects of Graphene Transfer and Thermal Annealing on Anticorrosive Properties of Stainless SteelJeong Hyeon Oh, Sang-Mok Han, Tae Yoon Kim — 2017
• Fabrication of (TiB/Ti)-TiAl composites with a controlled laminated architecture and enhanced mechanical propertiesHao Ding, Xiping Cui, Naonao Gao — 2021
• Pressure sintering of W-15wt.%Cu alloys prepared by mechanical alloying as a subsequent densification treatment methodZhi Li, Chunrong Jia, Liying Sun — 2006
• Additively manufactured SiC-reinforced stainless steel with excellent strength and wear resistanceYongming Zou, Chaolin Tan, Zhaoguo Qiu — 2021